4%20CIP, BMW educational info, Dokumentacja
[ Pobierz całość w formacie PDF ]
//-->Table of ContentsCIP - Coding, Individualization, ProgrammingSubjectPageIntroduction..........................................................................................2Purpose of the System........................................................................3Program Start.......................................................................................3General Rules for Programming..............................................................4Vehicle & Key Memory.........................................................................5Programming........................................................................................7Airbag Reactivation Procedure............................................................... 7Resetting and Correcting CBS Data....................................................... 7Review Questions.................................................................................9CIP - Coding, Individualization, ProgrammingModel: E65 - 745i / E66 - 745LiProduction Date: 11/2001 - E65, 03/2002 - E66Objectives of The ModuleAfter Completing this module, you will be able to:• List preconditions to perform CIP on a vehicle.• Understand the VKM “mask” to perform settings.• Perform Programming using CIP.• Perform control module initialization after Programming.• List the additional reference information needed for the rear seat side-impact airbagActivation/Deactivation.2CIPPurpose of The SystemThe “CIP” program was launched with the release of the DISplus CD - version 28.0. CIPProgramming is now contained on a separate CD for the DISplus/GT1 and will be updatedas an individual CD. For installation instructions refer to SI B09 03 02.Before proceedingon a vehicle, you must always refer to the latest version of SI B09 05 01 for additionaldetails and updated information!CIP stands forCoding, Individualization, Programming.• Coding - Updates and aligns (vehicle & country specific) the software resident in the con-trol modules.• Individualization - Vehicle and Key specific settings are changed according to customerrequests and stored in the Vehicle & Key Memory.• Programming - Data/programs in the control modules are activated (new - basic mod-ule) or updated (including coding to the specific vehicle).New Developments:• Graphic user interface, browser-based (clear display and on screen prompting).• Integrated compatibility and management program (automatic prompting in the selectionof hardware/software which must be installed/altered).• Integration, authentication and signature (protection against unauthorized access tocontrol modules).ProgrammingGeneral Rules for ProgrammingThe procedure for programming control modules on E65/E66 vehicles is controlled by theCIP program. The following preconditions must be followed when using the CIP program:• First connect the vehicle to an approved BMW battery charger (Deutronic AutomotivePower Processor -follow the instructions found in SI B04 11 02) and never disconnectduring programming. This charger must be connected in PS Power Supply Mode.• The date and time must be set correctly in the DISplus/GT1 ("Administration"-button oninitial startup screen to check and modify).3CIPGeneral Rules for Programming• Diagnostic head must be hard wired to thenetwork drop to ensure uninterrupted programming. (do not use radio connections)Using DISplus:1. DISplus2. SI LAN cable3. Diagnostic head4. DK LAN cableUsing GT1:1. GT12. LAN Adapter BT 1:13. SI LAN cable4. DK LAN cable5. Diagnostic head• Park the vehicle where it does not obstruct (programming may take up to 4 hours).• All control modules must be installed and functional.• Perform a fault memory deletion with“Quick Clearing”.• Readout and print Individualization settings with the CIP Program(Vehicle & Key Memorywill be deleted during programming).am• Read out (and print if applicable) Instrument Cluster/Control Display (mileage, ConditionBased Service data,radio station settings, etc.).• Engine must be off and cooled down (trans. oil temp. must be < 85º C).• Transmission in P or N position, vehicle must not move.w• Coding/Programming all control modules (with the ignition on - KL15), except the CAS.• Coding/Programming the CAS module with the ignition switched “off” and key removed.• Switch offallelectrical consumers.• Do not move seats, trunk lid, steering wheel, locks, windows, etc.• Warning: wipers can move unexpectedly (make sure path is clear and moisten glass).• Navigation CD V19.0 must be available when programming with CIP.•Print as you go for all CIP procedures (Measures Plan, Program abort, multiple attempts).• Initializing control modules (indicated on screen).• Re-establishing customer VKM settings overwritten during Coding/Program (reverts tofactory settings).4CIPProgram StartUsing DISplus or GT1 with the diagnostic headconnected to the vehicle, select “Coding/Programming” from the start mask.When the program is started for the first timeafter a CD installation, there is a longer wait time(approx. 90 seconds).• Start CIP by selecting “8 CIP”, then press theforward arrow. The initial CIP screen is thendisplayed.Note:After startup, CIP determines the vehicle order (VO) previously known as the CentralCoding Key (ZCS) and records which control modules are installed in the vehicle. The vehi-cle order is not displayed on the screen.Vehicle & Key MemoryBefore programming Vehicle & Key Memory (VKM), the customer must be informed aboutathe possible choices before delivery by filling out a Customer selection form (attachment #6of SI B09 05 01).The VKM screen displays all available VKM functions, their current settings, and the facto-ry default setting. Please refer toAttachment #5 of SI B09 05 01for a list of available VKMsettings for CIP.Note:VKM Values can only be determined by CIP if all VKM relevant control modules areOK (found and no faults). A “Short Test” is important, to verify that all control modules arefound before proceeding with coding or programming.• Press the "CKM" button at the screen with the text "Program SELECTION: Load soft-ware, Car & Key Memory (CKM)” as shown above.5CIP
[ Pobierz całość w formacie PDF ]
zanotowane.pldoc.pisz.plpdf.pisz.plstyleman.xlx.pl
|