4327-TE, MAKITA Budowa, Instrukcje serwisowe
[ Pobierz całość w formacie PDF ]
//-->TECHNICAL INFORMATION4326, 4326M, 4327, 4327M, 4328, 4329, M438, M439Jig SawModel No.DescriptionPRODUCTP 1/ 7LCONCEPT AND MAIN APPLICATIONSThese models have been developed as the successor models of 4322 series.In addition to the advantages of the predecessor models, 4326 series models featurethe following benefits:450W continuous rating inputNew exterior design and ergonomic handle with rubberized soft gripChange lever for 3 orbital settings and straight cutting (4328, 4329 and M439 only)HWModel 4329Dimensions: mm (")with steel plate base 217 (8-1/2)Length (L)with aluminum base 223 (8-3/4)Width (W)77 (3)Height (H)197 (7-3/4)SpecificationVoltage (V)110120220230240Current (A)4.33.92.22.12.0Cycle (Hz)50/6050/6050/6050/6050/60Continuous Rating (W)InputOutput450---450450450270270270270270Max. Output (W)420420420420420Model43264326M43274327MM43843284329M439SpecificationNo load speed:3,100500 - 3,100strokes per min.Length of stroke: mm (")18 (11/16)Shank typeB-typeMakita-typeB-typeMakita-typeB-type*1B-typewith B-type blade: 65 (2-9/16), with Makita type blade: 40 (1-1/2)Capacities: Woodmm (") Steel6 (1/4)Cut settingsStraight cutting3 Orbital settings + Straight cuttingVariable speed controlNoYesby dialMaterial of baseSteel plate*2Steel plate Steel plate*2Steel plate Steel plate*2Steel plateAluminumHousing colorMakita-blueNatural greenMakita-blueNatural greenToolless blade changeNoConnectable to vacuumYesDouble insulationYesPower supply cord: m (ft)2.0 (6.6)with steel plate base: 1.8 (4.0)Net weight: kg (lbs)with aluminum base: 1.9 (4.2)*1:Model M438 is also available with Makita-type shank.*2:Models 4326, 4327 and M438 are also available with aluminum base.Standard equipment4326, 4327, 4328, 4329, M4394326M, 4327M, M438Jig saw blade No. B-10 ... 1 pcJig saw blade No.10 ........ 1 pcHex wrench 3 .................. 1 pcHex wrench 3 .................. 1 pcNote:The standard equipment for the tool shown above may differ by country.OptionalaccessoriesHose 28-1.5Hose 28-3.0Jig saw bladesPlastic carrying caseGuide rule setKerf boardP2/7RepairCAUTION: Unplug the machine and remove the jig saw blade from the machine for safetybefore repair/ maintenance in accordance with the instruction manual![1] NECESSARY REPAIRING TOOLSCode No.1R2691R291DescriptionBearing extractorRetaining ring S and R pliersUse forRemoving Bearing case complete from Armature ass'yRemoving Ball bearings 627LLB and 608DDWRemoving retaining rings[2] LUBRICATIONApply 7g in total of Makita grease N. No.1 to the portions designated with gray arrows and a little amount of that tothe portions designated with the white arrows to protect parts and product from unusual abrasion.Fig. 1 (4326, 4326M, 4327, 4327M, M438)Large oval hole of Balance plate wherethe cylinder of Gear complete contactsContact surface of Pin 3 and Balance plateContact surface of Pin 3and Balance plateContact surface ofThrust plate and Bearing casecompleteContact surface ofThrust plate and Balance plateContact surface of Collar sleeveand SliderFig. 2 (4328, 4329, M439)Contact surface of Pin 3 and Balance plateContact surface of Balance plateand Gear completeContact surface of Collar sleeveand SliderLarge oval hole ofBalance plate wherethe cylinder of Gearcomplete contactsContact surface ofPush plate andBearing case completeContact surface of Push plateand Balance plateP3/7Repair[3] Disassembling of Housing R1) Remove Base and M4x16 Hex. socket head bolt using Hex. wrench 3 (Standard accessory).2) Slide the the protrusions of Dust cover and remove Dust cover from Housing set. (Fig.3)3) Remove nine 4x18 Tapping screws and one 4x35 Tapping screw. Housing R can be removed. (Fig.3)Fig. 3Depressionsin the grooves of Housing setTapping screw 4x35Tapping screw 4x18: 9 pcs.Protrusionsof Dust coverNote: Be sure to slide the protrusions out ofthe depressions.[4] Disassembling Gear SectionRefer toFigs. 4(4326, 4326M, 4327, 4327M, M438) and4a (4328,4329, M439).1) Remove Slider section from Collar sleeve.2) Remove Collar sleeve from Gear complete. As for 4326, 4326M, 4327, 4327M and M438, Bearing case complete,Thrust plate and Gear complete can be removed in this step.3) As for 4328, 4329 and M439, remove Retaining ring S-6 from the pin of Bearing case complete using 1R291.Bearing case complete, Push plate, Balance plate and Gear complete can be removed.Fig. 4Bearing case completeThrust plateBalance platePin 3Gear completeCollar sleeveSliderFig. 4aPush plateBearing case complete Balance platePin 3Gear completeCollar sleeveSliderDust sealRetaining ring S-6Polyurethane sponge sealSeal plate[Slider section]Slider guideSlider supportSlider guidePolyurethane[Slider section] sponge sealP4/7Repair[5] Assembling Gear SectionRefer toFigs. 4 and 4a.1) Assemble Armature ass'y to Bearing case complete.2) As for 4326, 4326M, 4327, 4327M and M438, mount Thrust plate on Bearing case complete. (Fig.4)As for 4328, 4329 and M439, after inserting Thrust plate to Dust seal, mount them on Bearing case complete. (Fig.4a)3) Connect Armature shaft gear and the pin of Bearing case complete to Gear complete through the holes of Balance plate.As for 4328, 4329 and M439, fit Retaining ring S-6 into the groove of the pin of Bearing case complete using 1R291.4) Face the collar side of Collar sleeve to Gear complete, and mount Collar sleeve on Gear complete.5) Put Collar sleeve into the hole of Slider section after assembling the components.[5] Removing Armature ass'yRemove Armature ass'y from Bearing case complete using 1R269 as illustrated inFig. 5.Fig. 5Bearing case complete1R269Armature ass'y[6] Removing Lever 18 (only for 4328, 4329 and M439)Refer toFig. 6.1) Remove Stop ring E-4 behind Lever 18 using a slotted screwdriver.2) Align Lever 18 with III mark on Housing set and pull out Lever 18.Steel ball 4 and Compression spring 4 can be removed.Fig. 6III markLever 18P5/7Repair[7] Assembling Housings R and LReferring toFig. 7,Assemble Fig.R to Housing L.Note: 1) Firmly insert O rings into the bottom of holes in Housing R so as not to fall off. (The bottom positions haveribs for prevention of falling them off.)2) Be sure to set each component in place of Housings R and L. Do not pinch Polyurethane sponge seal.3) Do not put Leaf spring under Slider. Insert Leaf spring to the holder of Housing R so that the Leaf springis parallel to Slider section and vertical to Housing L.Fig. 54326, 4326M, 4327, 4327M, M4384328, 4329, M439Slider sectionHousing LSlider guideSlider supportPolyurethanesponge sealPolyurethanesponge sealwith SealplateO ringParallelSlider sectionVerticalHolder forLeaf springHousing L
[ Pobierz całość w formacie PDF ]
zanotowane.pldoc.pisz.plpdf.pisz.plstyleman.xlx.pl
|