4331D-TE, MAKITA Budowa, Instrukcje serwisowe

[ Pobierz całość w formacie PDF ]
//-->TECHNICAL INFORMATION4331D, 4333DCordless Jig SawModels No.DescriptionPRODUCTP1/4L.1CONCEPTION AND MAIN APPLICATIONSThe above models have been developed as a series of thetop-handle type of cordless jig saw.* Model 4331D : 12V type with variable speed control feature* Model 4333D : 14.4V type with variable speed control featureThe variations of these models are as follows.Model No.4331DWD4331DWAE4331DWDE4333DWD4333DWAE4333DWDEBatteryNi-MH 1234 : 1 pc.Ni-Cd 1222 : 2 pcs.Ni-MH 1234 : 2 pcs.Ni-MH 1434 : 1 pc.Ni-Cd 1422 : 2 pcs.Ni-MH 1434 : 2 pcs.ChargerDC1411DC1411DC1411DC1411DC1411DC1411*Charging time forone battery packapprox.75 min.approx.60 min.approx.75 min.approx.75 min.approx.60 min.approx.75 min.HWL.2Dimensions : mm ( " )70 (2-3/4)Width ( W )Height ( H )217 (8-1/2)Length ( L.1 )280 (11)153 (6)Length ( L.2 )Specification*Charging time for one battery pack: The above time may change, which depends on the conditionsof battery, charger, etc.4333D500 - 2,60026 (1)(2-9/16)(3/8)(13/16)4331DModel No.Strokes per min.: (min-1= spm)500 - 2,800Length of stroke : mm ( " )65Max.cutting in wood: mm (")10capacities in mild steel: mm (")20in aluminum: mm (")Standard equipment*Jig saw blade set ....................1 set (including Jig saw blade No.B-10 : 2 pcs., BR-13 : 2 pcs., and B-22 : 2 pcs.)*Hex wrench 3 ....................... 1 pc.*Kerf board....................... 1 pc.*Plastic carrying case ............. 1 pc.< Note > The standard equipment for the tool shown may differ from country to country.Optionalaccessories* Jig saw blades of MAKITA type : No. 1 - 5, No.8 - 10, No.16, No.17, No.41, No.42, No.BR-3* Jig saw blades of B type : No.51, No.58, 59, B-10 - B19, B-21 - B-27, B16L, BR-13* Battery 1200, 1202, 1201A, 1220, 1222, 1234, 1235 (for 4331D)* Battery 1420, 1422, 1433, 1434, 1435 (for 4332D and 4333D)* Rip fence* Vacuum head* Circular guide* Battery cover* Protector* Charger DC1411* Plastic base plate* Fast charger DC1422* Kerf board set* Fast charger DC1439* Hose setRepair< 1 > Disassembly and assembly of mechanical partsDisassemble the gear housing cover from the main tool-body by removing thefour tapping screws 4x18.Gear housing coverP2/4Tapping screw 4x18Fig.11) Gear housing cover1. Remove thrust plate from slider. (See Fig.2-1.) And then, remove slider by unscrewingcountersunk hd.screw M4x10 with a straight T20 torx bit. (See Fig.2-2.)So, rod can be removed from gear housing cover. (See Fig.2-3.)Gear housingcoverGear housingcoverGear housing coverFig.2-1Thrust plateCountersunkhd.screw M4x10Fig.2-2HolderFig.2-3Slider2. Attach holder under flat section of rod. See fig. 3.3. Attach slider to rod, making sure that the flat surface on the slider matches the flat surface on rod. See Fig. 3.4. Tighten countersunk hd.screw M4x10 used to hold the slider. See fig. 3.5. Set thrust plate on slider with the folded ends toward the inside of the gear housing cover. See fig. 3.RodHolderFlat section of rodSliderCountersunkhd.screw M4x10Thrust plateFig.3Repair< 2 > Assembly of the parts in housing set1) Balance plates are not symmetric. Assemble the balance plate as shown in Fig.4.This portion has to be faced to thelever 17 side.P3/4Lever 17Fig. 42)Tighten countersunk hd.screw M4x10 with a straight T20 torx bit for mounting pin 8. Note the alignment of pin 8.The hole in the center of pin 8 must be positioned in the same direction as the tabs on motor bracket asshown in Fig. 5.Pin 8Motor bracketHoleTabTabFig. 5Countersunk hd.screw M4x103)Assemble the internal parts as shown in Fig.6, and joint crank complete and helical gear 58by tightening hex socket hd.bolt M4x16Hex sockethd.bolt M4x16Retainingring S-8Flat washer 6Pin 6Needlebearing 607Crank shaftFlat washer 26Flat washer 6Balance plateFlat washer 6Pin 6Flat washer 5Pin 5Fig. 6Flat washer 6Push plateFlat washer 26helical gear 58RepairP4/44) Attach gear housing cover to housing set so that needle baring 607 is aligned with the slot portion of slider.Gear housingcoverHousing setSlot portionof sliderNeedle bearing 607CircuitFig. 6diagram(Model 4331D and 4333D)WhiteBattery holderBlueBlackYellowPurpleFETFig. 723SwitchOrangeControllerRedBlackDC motorWiringdiagram(Model 4331D and 4333D)ControllerSwitchPush lead wires (Blue and Orange)to the bottom of housing to preventinterference by lock off button.Fix lead wires(Blue and Orange)with lead holder.DC MotorFix lead wireswith lead holder. [ Pobierz całość w formacie PDF ]

  • zanotowane.pl
  • doc.pisz.pl
  • pdf.pisz.pl
  • styleman.xlx.pl

    		•